Culligan GoodWater Machine DrinkingWater System Specifications download pdf (Page 15)

INSTALLATION / 13

6. Feed the monitor cable, if used, down through the

faucet base. Be sure that all twists are eliminated from

the cable.

7. Position the monitor cable in the notch of the base;

locate the air gap port on the inner body opposite the

cable notch, slide the inner body or faucet assembly

onto the base. Fasten to the base using two #6-32 x

3/8" Phillips round head screws.

NOTICE: Skip steps 8 through 11 if the faucet has been

preassembled.

8. Align the air gap hole in the outer body with the air gap

port and slide the outer body over the inner body until it

meets the base. Position the monitor cable in the notch

on the outer body closest to the final position of the

display.

9. Screw the stem into the large hole in the inner body

until the handle on the stem is lined up with the air gap

port.

10. Position the lever clearance slot over the lever and slide

the top inner body over the stem until it contacts the

outer body. Secure the top inner body using two #6-32

x 7/8" Phillips round head screws. Check to make sure

that the handle operates smoothly.

11. Push excess monitor cable back through the faucet

assembly and position the display on the top inner body

so that it is readable. It may be necessary to pull gently

on the monitor cable from below the sink.

12. Slide the cap/spout onto the faucet assembly until the

circular boss on top of the inner body is flush with the

top of the cap. If a monitor is installed, be sure that the

display is visible through the window in the cap.

Fasten the cap to the faucet assembly using the #4-40 x

3/8" Phillips flat head screw. Be careful not to damage

the head of this screw as it is always visible.

When used, feed the monitor cable through the top

inner and outer bodies. Do not position the monitor

display at this time. NOTICE: Monitors preassembled

to a faucet require working with close assembly toler-

ances. All twists must be eliminated from the cable to

properly align and assemble faucet body components.

4. Chrome Faucet Only - Based on whether the installa-

tion is right or left handed and if a monitor is to be used,

insert the spout through the top cap and install the

retaining ring into the top groove of the spout.

5. Lubricate the stem seal ring and the o-ring with food

grade lubricant, PN 00-4715-07. Push the stem seal

ring firmly into the stem. Install the stem seal back up

ring on top of the seal.

6. For in-shop preassembly, complete Installation/Assem-

bly steps 6 through 12. Otherwise, begin the

INSTALLATION/ASSEMBLY sequence with step 3

at the installation site.

Installation/Assembly

NOTICE: If the faucet has not been preassembled, begin the

INSTALLATION/ASSEMBLY sequence with step 3 at the

installation site.

CAUTION: Plastic parts will break if screws are

overtightened.

1. Remove the top cap/spout (preassembled faucets only).

2. Insert a #1 Phillips screwdriver through the clearance

slots and remove the faucet base (preassembled faucets

only).

3. Center the gasket over the 1-1/4" sink hole. Orient the

notches in the 3, 6, 9 and 12 o’clock positions. Place

the faucet base on top of the gasket and push the toggle

bolts through the sink hole. The cable notch in the base

should be on the opposite side of the desired handle

position and should line up with one of the notches in

the gasket.

4. Slide the installation tool into the base. The “T” on the

tool will be on the handle side of the faucet. Align the

base by making the stem of the “T” line up with the

back of the sink, and the crossbar of the “T” point straight

out of the sink. Hold the assembly tool down and tighten

the toggle bolts. Remove the installation tool and check

that the toggles are firmly seated on the sink.

5. Connect drain inlet and drain outlet tubing to the black

inner body. Push the 1/4" (blue is recommended) con-

centrate inlet tube securely onto the concentrate inlet

barb. Be sure to use enough tubing. Slide the 1/2"

black concentrate tube snugly onto the concentrate out-

let nipple. Feed these tubes down through the faucet

base.

FIG. 10

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 26 27

Comments to this Manuals

No comments

Culligan GoodWater Machine DrinkingWater System Specifications Page 15

Comments to this Manuals

Related products and manuals for Water dispensers Culligan GoodWater Machine DrinkingWater System